For the complete documentation index, see llms.txt. This page is also available as Markdown.

RTK fix loss on job sites

Why an RTK fix drops on construction and survey sites, how to tell whether the sky view, the data link or the correction source is at fault, and how to prevent and recover from fix loss mid-job.

An RTK fix can be lost in four places: the sky above the antenna, the receiver, the data link that carries the corrections, and the correction source itself. Each one leaves a different trace on the receiver, and each one has a different fix. On a large or busy site the first three cause most dropouts, and the correction source is the one an operator can do least about on the day.

Causes by layer

Layer
What breaks
What the receiver shows

Sky view

Buildings, cranes, steel, trees, cuts and machines block or reflect satellite signals.

Satellite count and signal strength fall, DOP rises, and the solution drops to float at the same spots each time.

Receiver

A low elevation mask, a tilted or moving antenna, or the GGA heartbeat switched off.

Corrections arrive on time, but the fix is slow to come back or positions drift as the rover moves away.

Data link

Mobile coverage is weak across part of the site, or the SIM, controller or Wi-Fi link stalls.

The correction age climbs for several seconds before the fix is lost.

Correction source

A correction network or its link to the caster goes down.

Every rover on the same service loses corrections at the same moment, wherever it stands.

Ionospheric activity sits outside all four layers. During a disturbed period, receivers on every correction service take longer to fix and lose it more easily, and the effect is strongest on services that rely on a single distant base station.

Diagnosis by symptom

Symptom
Most likely cause
First check

The fix drops at the same places on every pass.

Sky view

Note the spots and look up. Reroute through open ground, or measure those points from a better position.

The correction age climbs before each drop.

Data link

Check the mobile signal at that spot and try a SIM on another carrier.

Corrections arrive with a normal age, but the receiver stays on float across the whole site.

Geometry or the ionosphere

Check the DOP and the satellite count, wait a few minutes, and compare with a second rover.

One rover drops while another nearby holds its fix.

That rover

Compare the settings, the antenna, the SIM and the firmware of the two units.

Every rover drops at the same moment.

Correction source

Note the time. In an Eligible Area the service moves to the next network. Elsewhere, contact support.

The fix holds, but positions drift as the rover moves across a long site.

GGA heartbeat

Confirm position sending is on. See Mountpoint selection and the GGA heartbeat.

A receiver that reports a fix while repeat measurements disagree has not lost its fix. That pattern points to a false fix or multipath, which Inconsistent RTK accuracy on site covers.

Site planning

Construction sites change daily. A crane goes up, a stockpile grows, a steel frame rises, and a spot that held a clean fix last week loses it this week. Plan for that before the job starts.

  • Check how many correction networks cover the site on the coverage map. Where two or more networks overlap, RTK Premium has smart failover available when a network drops. Where one network covers the site, a network outage stops corrections until it returns.

  • Walk or drive the site with a phone or a receiver and check mobile data at the far corners, in cuts below grade and next to steel structures. Mobile coverage on a large site is rarely even.

  • Consider a multi-operator SIM on sites where one carrier is weak. Our IoT SIMs are not tied to one mobile network.

  • Set control and check points across the site, clear of reflective surfaces, so a crew can confirm a fix anywhere on the job within a short walk.

  • Keep the GGA heartbeat on for machines and rovers that cover long distances. The network builds each correction for the position the receiver reports, so a stale position degrades the correction as the rover moves away.

  • Check the correction age limit in the receiver. Many receivers hold a fix through a short gap in corrections and drop to float once the age passes that limit, so a limit set too short turns every brief data gap into a lost fix.

  • Mount machine antennas clear of the cab, the boom and the counterweight, and check the mounting again after any repair.

Recovery procedure

  1. Stop measuring as soon as the status leaves fixed. Set the data collector to store fixed solutions only, so a float point cannot be recorded by mistake.

  2. Read the receiver before moving: the correction age, the satellite count and the DOP. Those three values identify the layer in most cases.

  3. Move to open sky and let the receiver fix again. If the correction age is climbing, solve the data link first, because the fix cannot return without corrections.

  4. Re-measure the last point you trust, or the nearest check point, and compare it with the stored value. Resume only when the two agree within the job tolerance.

  5. Re-measure any point taken between the last good check and the drop.

  6. Log the time of the drop. If every rover on site lost corrections at once, send support that time together with the receiver model, the mountpoint, the solution status and the correction age.

Support runs on business days from 09:00 CET to 17:00 ET at info@premium-positioning.com or +31 85 0606 338.

FAQ

Why does my RTK fix keep dropping on a construction site? Most dropouts on a construction site come from obstructions such as cranes, steel and stockpiles, or from weak mobile coverage in parts of the site. A drop at the same spot each time points to the sky view, and a correction age that climbs before the drop points to the data link.

How do I know whether the correction service caused the dropout? A correction source failure hits every rover on that service at the same moment. A drop on one rover, or at particular spots, starts at the site or the receiver.

Will RTK Premium keep my fix if a correction network goes down? In an Eligible Area, RTK Premium moves to the next network that covers your site, and the receiver may lose its fix briefly before fixing again. In an area served by one network, corrections stop until that network returns.

Can I keep measuring on a float solution? A float solution is typically accurate to decimetres rather than centimetres, so it is not fit for survey or stakeout work. Stop, restore the fix and check a known point before you continue.

How long should a receiver take to fix again after a dropout? In open sky with corrections arriving, a modern multi-constellation receiver usually fixes again within a minute. A longer wait points to the data link, poor geometry or ionospheric activity.

Does a better SIM help with RTK dropouts? It helps when the correction age climbs before the drop, because that pattern means the data link is failing. A multi-operator SIM is not tied to one mobile network, which matters on a site where one carrier is weak.

Last updated: 15 October 2026

Was this helpful?