> For the complete documentation index, see [llms.txt](https://docs.premium-positioning.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.premium-positioning.com/guides/machine-control.md).

# Machine control

Connect Leica iCON, Topcon 3D-MC and Trimble Earthworks machine control to RTK Premium over NTRIP: settings, the network type to choose, and job-site essentials.

RTK Premium corrections work with machine-control and grade-control systems from Leica, Topcon and Trimble over NTRIP. Every system uses the same caster settings, and the guides below give the menu path for each one. In a fixed solution under good GNSS conditions, the GNSS position reaches under 1.5 cm horizontally and 2.5 cm vertically. Accuracy at the blade or bucket also depends on the machine's own sensors and calibration.

### Supported systems

| System                                                                                                                | Manufacturer | Set up in                              | Setting to choose                        |
| --------------------------------------------------------------------------------------------------------------------- | ------------ | -------------------------------------- | ---------------------------------------- |
| [Leica iCON iGD4](https://docs.premium-positioning.com/guides/machine-control/leica-icon-igd4.md)                     | Leica        | iGD4 display                           | Connect via NTRIP, network type VRS      |
| [Leica iCON iCG70 / iCG70 T](https://docs.premium-positioning.com/guides/machine-control/leica-icon-icg70-icg70-t.md) | Leica        | Leica iCON field software or Captivate | Rover, Network, NTRIP                    |
| [Topcon Pocket-3D / 3D-MC](https://docs.premium-positioning.com/guides/machine-control/topcon-pocket-3d-3d-mc.md)     | Topcon       | Pocket-3D                              | Direct Network Connection, RTCM 3.x, VRS |
| [Trimble Earthworks](https://docs.premium-positioning.com/guides/machine-control/trimble-earthworks.md)               | Trimble      | Earthworks display                     | Internet (NTRIP), RTCM 3.x, VRS          |
| [Trimble SPS986](https://docs.premium-positioning.com/guides/machine-control/trimble-sps986.md)                       | Trimble      | Trimble Siteworks                      | Internet (VRS)                           |

Menu labels differ between software versions, so each guide notes where to look for the nearest equivalent.

### Settings for every system

| Setting                   | Value                   |
| ------------------------- | ----------------------- |
| Caster address (host)     | rtkpremium.xyz          |
| Port                      | 2101                    |
| Mountpoint                | COMMON                  |
| Correction format         | RTCM 3.x                |
| Network type, where asked | VRS                     |
| Send position (GGA)       | On                      |
| Username and password     | From your account email |

### How corrections reach the machine

The GNSS receiver on the machine, or its display, connects to the RTK Premium caster over a mobile data connection. It sends its position up as a GGA message, receives RTCM 3.x corrections built for that position, and passes the corrected position to the machine-control system. The heartbeat has to keep flowing while the machine moves, or the network keeps correcting for where the machine started. [Mountpoint selection and the GGA heartbeat](https://docs.premium-positioning.com/troubleshooting/mountpoint-selection-and-the-gga-heartbeat.md) explains why.

### On the job site

* Data connection: the display needs a live internet connection while the machine works. A machine that takes a SIM can use [Premium Positioning IoT SIMs](https://docs.premium-positioning.com/learn/rtk-corrections-and-iot-sims-from-one-supplier.md), which can use more than one operator in most countries, so the machine is not tied to one mobile network.
* One login per machine: one login runs one session at a time, so each machine and each rover needs its own subscription.
* Correction sources: where two or more networks cover the site, smart failover moves the service to the next network when one drops. The [coverage map](https://www.premium-positioning.com/coverage?utm_source=docs\&utm_medium=referral\&utm_campaign=docs\&utm_content=machine-control) shows how many networks serve your site.
* Site calibration: when a project uses a site calibration, make sure every machine and rover on site uses the same calibration and the same correction service, so their positions agree.
* Subscriptions: the [XYZ Platform](https://rtkpremium.xyz/sign-in) shows every machine's subscription and the live status of each session in one place.

When a fix drops on site, [RTK fix loss on job sites](https://docs.premium-positioning.com/troubleshooting/rtk-fix-loss-on-job-sites.md) helps you tell an obstruction, a data-link drop and a correction-source outage apart.

### FAQ

Which network type should I choose on a machine-control display? Choose VRS where the display asks for a network type, with RTCM 3.x as the correction format and COMMON as the mountpoint.

Can machines and rovers on the same site use RTK Premium together? They can. Every device uses the same caster settings, and each needs its own subscription and login.

What accuracy does machine control get with RTK Premium? The GNSS position reaches under 1.5 cm horizontally and 2.5 cm vertically in a fixed solution under good conditions. Accuracy at the blade or bucket also depends on the machine's sensors and calibration.

Does RTK Premium work with a fleet that mixes Leica, Topcon and Trimble? It does, because every system connects over standard NTRIP with the same settings. [One RTK service for Trimble, Topcon and Leica receivers](https://docs.premium-positioning.com/learn/one-rtk-service-for-trimble-topcon-and-leica-receivers.md) covers mixed fleets.

What data connection does a machine need? The display or receiver needs a live internet connection for as long as the machine works. Corrections use roughly 100 to 300 MB a month in normal field use, and a machine that streams around the clock uses more.

My system is not listed. Can I still connect it? Any system that accepts RTCM 3.x corrections over NTRIP can connect. [Connect a receiver](https://docs.premium-positioning.com/set-up-and-connect/connect-a-receiver.md) has generic steps, and [All devices A to Z](https://docs.premium-positioning.com/guides/all-devices-a-to-z.md) lists every guide.

Last updated: 12 November 2026
